Jump to content

jkostelni

Member
  • Content Count

    28
  • Joined

  • Last visited

  • Feedback

    %

Community Reputation

0 Neutral

About jkostelni

  • Rank
    ASF Immigrant
  • Birthday 11/05/1998

Profile Information

  • Gender
    Male
  • Location
    Virginia
  1. Ok so new info idk if it'll help but when it stops shooting and I give it a good shake it will shoot again.
  2. I've tried with and without the mosfet. It fires every now and again for seemingly no reason. How does one check circuit continuity?
  3. So my A&K sr25k has been shooting fin up until today. I was shooting it and I all of a sudden it stopped shooting. No sound or any other reaction. I've tried three batteries both with and without my Burst Avocado-II Programmable Fire-Controller. Does anybody have any clues what the problem could be?
  4. I tried to charge my Lipo with my Tenergy B450AC which has worked before but all of a sudden I have been getting ERR5 which according to the manual this means that there is an internal error and that I should turn it off and back on does not work than to contact the manufacturer for further trouble shooting. I sent Tenergy customer support an email but I am not expecting to get a reply. It works just fine for charging my NiMH battery but whenever I have the balance charger plugged in I get the ERR5. I also checked to make sure that the battery was not dead and the output voltage was a safe 3.5v. Does anybody have any clue whats going on? Update: I tried again and the LCD display no longer works except to show error messages.
  5. Over my airsoft career I have dreamed about being able to go to a MILSIM op but, I always assumed that there would never be one close enough to me to make it even remotely possible. As it happens MILSIM West is hosting their Balkar Ridge event only two hours away form me! While this is great because it is so close, I am pressed for time to come up with the funds to be able to attend. The cost of the tickets are $150-$175. Before the event I would also like to pick up some more gear before the event (better goggles, more mags, etc). For anyone who will be there I plan to attend as a member of the Cossack Militia and would I be very grateful if someone would take me under their wing and show me the ropes of actual MILSIM events. Check out my GoFundMe: https://www.gofundme.com/my-first-milsim-event Sorry is this against the rules or in the wrong place!
  6. Over my airsoft career I have dreamed about being able to go to a MILSIM op but, I always assumed that there would never be one close enough to me to make it even remotely possible. As it happens MILSIM West is hosting their Balkar Ridge event only two hours away form me! While this is great because it is so close, I am pressed for time to come up with the funds to be able to attend. The cost of the tickets are $150-$175. Before the event I would also like to pick up some more gear before the event (better goggles, more mags, etc). For anyone who will be there I plan to attend as a member of the Cossack Militia and would I be very grateful if someone would take me under their wing and show me the ropes of actual MILSIM events. Check out my GoFundMe: https://www.gofundme.com/my-first-milsim-event Sorry is this against the rules or in the wrong place!
  7. Ok I'd rather use this opportunity to learn. What tools might I need? If the nozzle is cracked is this what I need or is it something else? If the nozzle isn't cracked where else should I look for problems? Also, there is a small switch next to the hammer that resets the trigger and the slide usually needs extra help to push all the way up.
  8. So I tried the freezer method and the leak was much louder. The gun also only got one shot off in semi before not coming up all the way an spraying gas out of the barrel.
  9. Is the cracked nozzle easy to fix? I know with the G18C its hard to find parts. Do you know where I could find some?
  10. I just bought a used KSC G18C and for some reason I can never get off a full mag before the slide doesn't come all the way up and sprays all the remaining gas. Especially when I put it in full auto it does this after about 2-3 shots. I hear a small leak at the top of the mag but it does this even when I shooting immediately after filing it. Side note: This isnt caused by the temp of the mag or low gas can because I keep everything indoors and the gas is brand new.
  11. I just bought a used KSC G18C and for some reason I can never get off a full mag before the slide doesn't come all the way up and sprays all the remaining gas. Especially when I put it in full auto it does this after about 2-3 shots. I hear a small leak at the top of the mag but it does this even when I shooting immediately after filing it. Side note: This isnt caused by the temp of the mag or low gas can because I keep everything indoors and the gas is brand new.
  12. I recently bought the A&K SR25K and three A&K SR25 midcap magazines for it. For some reason the midcaps take a lot of extra wiggling and pushing to get it to lock into the gun. The high cap the the gun came with goes in just fine but the midcaps wont. As far as I can tell the locking mechanism for the midcaps is exactly like the the high cap.
  13. I have an R9 270x that I have been looking to get rid of. It has seen plenty of use but it still works like a dream! The only thing that I am missing from it is the original box... I do have the box from the card that I replaced it with that I could ship it in.
  14. jkostelni

    .30g Tracer BBS

    It's for outdoors. I'm not very knowledgeable of airsoft parts so here is the link to where I bought the gun. https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwj299zzrsnRAhUo0oMKHe9dDO0QFggaMAA&url=http%3A%2F%2Fwww.evike.com%2Fproducts%2F29292%2F&usg=AFQjCNE_bh-o84NaAcUzK7WwHQJdAXU8wQ&bvm=bv.144224172,d.eWE
  15. jkostelni

    .30g Tracer BBS

    Do you think I should completely convert from .30 to .25 or just mix in the .25 tracers? I know it would throw off the accuracy some but I do you think it would be significant enough to warrant not doing it?
×
×
  • Create New...