|
to add your 300x250 banner, pay ad zone 5 |
Airsoft Atlanta is your source for quality airsoft guns and rifle parts
to add your Text Link here, pay ad zone 3 
  or Check Out the ASF Store. If you can not help us financially, then at least help us by telling a friend: Share us on your favorite social networking website 
|
|
Search the Community
Showing results for tags 'DSG'.
The search index is currently processing. Current results may not be complete.
Found 5 results
-
So I have been teching on guns for a few years on and off. I think I'm finally ready for my first DSG build. My goal is about 50ish RPS at 320 FPS. Parts List siegetek DSG G&G Spur 18:1 SHS Bevel SHS pinion SHS HT Motor G&G Shell (with ARL reset) SHS Trigger Contacts G&G Trigger SHS Piston (Swiss Cheesed) SHS m170 Unknown Ball Bearing Spring Guide SHS Aluminum Piston Head(Changing this) ZCI Cylinder SHS cylinder head Unknown Tappet(Might be G&G) Unknown Air Nozzle Steel Cut Off Lever 1800 Mah 75C 11.1V Custom 150000 Mah 35C 11.1V (Buying Single cells and building it) I've done a preliminary build and I'm getting 47ish RPS and 270 FPS What can I do to get my gun to my goal thanks guys
-
okay so im thinking of doing shortstroking due to the amount of overspin im getting. I use an ab mosfet for this but the motor gets hot pretty quick while using the ab option. im already running at about 405 fps with perfect compression on a settled cyma stock spring that ive been running for about a year. I want to getthe same fps and don't want too much as in tennessee, at the airsoft fields I will play at, the fps limit is 370 with .25s but since they know me, they let me go a little over. so how can I achieve that fps with an m130 spring? how many teeth do I need to short stroke? keep in mind I don't own a dremel.
-
hey so my gun is having feeding issues again. EVEN WITH A SECTOR CHIP. at first it fed fine with the sector chip. now it's not. 11.1v doesn't work. 9.6 and below does. tappet plate is stock. tried putting another stock tappet plate in there. same thing. any ideas? should I get a new tappet that's reinforced? I was looking at shs EDIT: I'm also having overspin even with a new steel COL. only on 11.1. should I get a stronger spring for this?
-
I want to make sure to not buy the wrong gears. What are the 10:1 markings for the gears? They have like 20:15 and 10:44 I think.
-
So, I am thinking about building a DSG with an insane ROF and standard CQB FPS. Is there anything that is going to blow up with this setup? 16 AWG low resistance wiring GATE nanoABB 3rd Gen MOSFET http://www.evike.com/products/47824/ Deans SHS Trigger contacts 6mmproshop high speed high torque motor http://www.evike.com/products/51834/ or the Tienly version of this RiotSC DSG 8 tooth 10:1 gearset short stroked to 330ish fps m170 spring 250mm 6.01mm tightbore barrel lonex 70 degree soft bucking Lonex 15 tooth piston shortstroked and swiss cheesed. Tappet plate modified for DSG Shim job, Radiused gearbox and re-greased with white lithium grease. (the gun comes with good AOE as it is, so long as the new piston doesn't mess it up.) BOLT 65-130 CC 5400 MAH 11.1v LiPo everything else that comes stock in this gun http://www.evike.com/products/42392/ Will this blow up? If so why? Will the motor burn out with that spring? Will the lack of Sorbo and neoprene break the front of the gearbox? Should I not short stroke DSG gears? I wanted to use the m170 to avoid pre-engagement. What would the RPS look like? Will trigger response be slow because of the high speed motor? What would RPS be like with a Frankentorque motor?
