Jump to content

to add your 300x250 banner, pay ad zone 5
Airsoft Atlanta is your source for quality airsoft guns and rifle parts
to add your Text Link here, pay ad zone 3

AirsoftAtlanta.com AirsoftNMore.com Airsplat.com AirsoftRC.com
Vote for us to add your 180x30 banner here, pay ad zone 2

If you appreciate this website, please ASF Donation or Check Out the ASF Store. If you can not help us financially,
then at least help us by telling a friend: Share us on your favorite social networking website Bookmark and Share

Recommended Posts

No you wont. You need a bore up when you exceed 590mm. I am running a 550mm barrel on a Type 0 cylinder and have had no problems and have achieved my target fps of 400fps (or very close to it, it punches through the bottom of a pop can) with a m120 spring.

 

My question is, where did you find a Prommy 550mm barrel in stock? I've been looking all over for those.

Edited by airborne101

Share this post


Link to post
Share on other sites
No you wont. You need a bore up when you exceed 590mm. I am running a 550mm barrel on a Type 0 cylinder and have had no problems and have achieved my target fps of 400fps (or very close to it, it punches through the bottom of a pop can) with a m120 spring.

 

My question is, where did you find a Prommy 550mm barrel in stock? I've been looking all over for those.

 

Airsoft Atlanta has them in stock. http://www.airsoftatlanta.com/Prometheus_M...rel_p/58003.htm

Share this post


Link to post
Share on other sites
No you wont. You need a bore up when you exceed 590mm. I am running a 550mm barrel on a Type 0 cylinder and have had no problems and have achieved my target fps of 400fps (or very close to it, it punches through the bottom of a pop can) with a m120 spring.

 

My question is, where did you find a Prommy 550mm barrel in stock? I've been looking all over for those.

 

 

 

Good news, im trying to achive the same (400fps), im glad I don't have to spend the 70 bucks on a bore up kit, and I heard you can run into problems bore up. I got the prommy from airsoftatlanta, they are still in stock (6.03)....... thanks.

Share this post


Link to post
Share on other sites
No you wont. You need a bore up when you exceed 590mm. I am running a 550mm barrel on a Type 0 cylinder and have had no problems and have achieved my target fps of 400fps (or very close to it, it punches through the bottom of a pop can) with a m120 spring.

 

My question is, where did you find a Prommy 550mm barrel in stock? I've been looking all over for those.

 

Just curious airborne101, using an m-120 spring, what other parts/mods did you use to achive 400 fps?

 

thanks

Share this post


Link to post
Share on other sites

Hehe...

 

-Guarder Type 0 Cylinder

-Guarder Cylinder Head

-Guarder Air Nozzle

-Systema Duracon Piston Head with Bearing w/ #14 O-ring

-G&P Polycarb Piston

-Classic Army m120

-Prometheus NEO Strike Chamber

-Systema bucking

-SCS

-New wiring w/ Extreme Fire SW-AB-LONG MOSFET wired to deans

-G&P M120 Motor

 

Those are the internals in my rifle, excluding a tight bore barrel.

 

Too be honest, I don't know what the quality of JG is these days, but I am guessing you don't need to put those parts in there. From my understanding, JG's can handle a 400fps spring for quite a while. I think the only think you really need to do is reshim it and regrease it.

 

Also, please don't double post. Use the edit button on the bottom right corner of your previous post to add new information.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...