Jump to content

Recommended Posts

KWA Kriss Vector Infinity Build - infinite firepower for your GBB Vector for whom you can't find good mags anymore!

This works for all KWA GBB mags btw.

 

Supplies needed:

-CQB Russian HPA adapter valve for KWA fill valves

-Any Electric autowinding box mag (I used A&K M249 mag)

-CA Glue and Zip Kicker (optional)

-JB weld epoxy (the tubes, and faster cure time is better) can be found at walmart

-Ideally 1*7.5*1000mm steel extension spring

(I've only found .5*8*1000 and that worked for me https://m.aliexpress.com/s/item/32812313986.html?spm=a2g0n.search-cache.0.0.70bc08b9FMNRwW#autostay)

You might want to double check the minimum diameter of the bottom of your mag's bb reservoir using a micrometer/calipers because all mags are different.

 

Also spend time trying to find a spring with a thicker wire diameter than the 0.5mm that I used, because it's pretty slinky. It's tough tho. If you do, *please* link me it.

 

1. Install the HPA Valve and take out the spring and guide assembly out of your mag.

 

2. Insert the extension spring into the bottom of your mag until it stops. Make sure you take out the reservoir parts before permanently fixing this spring in.

 

3. Use CA glue+zip kicker, or JB weld along the contact line of the bb reservoir and spring to affix it into the reservoir

 

4. Take a >1in piece of rigid tube that's wide enough to slide over the spring. I find larger plastic pen barrels work, but you can use anything you want.

Slide it up the spring up to the bottom of the mag, and apply generous amounts of JB weld to the magbase-tube connection.

 

5. Optional, but use some kind of flexible rubber tube to slide halfway over the tube you just glued to provide some play in case the bottom of the mag is pushed against something. You don't want your spring to get bent out of shape. I used the rubber grip off the pen I used for the previous section. Tape of any kind should be okay.

 

5. Take an electric box mag and JB weld the feed spring on it in a similar fashion. You may need to remove the release lever on the mag's feed lip that keeps BBs in, or remove the feed lip totally.

On my A&K M249 mag, upon removing the mag's top part that clips into the gun, there was already a metal spring with a widened portion that I could stick my spring into and glue it.

 

6. Splice and solder adequately long (3 or wires onto the pressure switch for your mag,

or if the mag doesn't have that, disassemble it and splice/solder the switch wire onto the segment of positive wire coming after the switch and battery.

 

7. Tape the switch onto your gun wherever you like.

 

8. Use 3+ ft of 3/4 in or wider plastic wire conduit (flex tubing) to wrap around your hpa/bb/switch lines.

It's the stuff you see wrapped around the wires in your car's engine bay, you can get it at NAPA auto parts and sometimes Lowes or Home Depot.

You can also use other stuff like mesh tubing as long as it protects your lines from snagging.

 

And BLAMO, now you have INFINITE firepower from your Vector without paying $100s for new mags!

Edited by drderpityderp

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...