Jump to content

to add your 300x250 banner, pay ad zone 5
Airsoft Atlanta is your source for quality airsoft guns and rifle parts
to add your Text Link here, pay ad zone 3

AirsoftAtlanta.com AirsoftNMore.com Airsplat.com AirsoftRC.com
Vote for us to add your 180x30 banner here, pay ad zone 2

If you appreciate this website, please ASF Donation or Check Out the ASF Store. If you can not help us financially,
then at least help us by telling a friend: Share us on your favorite social networking website Bookmark and Share
Guest

Show Off Your Rifle!

Recommended Posts

That EBR looks beautiful. How much was it? I've always wanted a WE EBR, but the cost is normally prohibitive to me.

 

I bought it second hand on craigslist. The guy said it had a broken trigger pack. He sold it to me for $200 plus $40 shipping which included the scope, bipod, and gun bag because of the trigger. It was about a 20 minute fix. I basically did a trigger job like any real steel rifle, didn't even need to buy any parts, except for some of the Mother's that I used to polish the trigger and sandpaper to file some pieces down. It's a WE EBR. I didn't even know that this gun was a limited production. I was just looking through airsoft ads and this gun looked cool.

Edited by egalsim

Share this post


Link to post
Share on other sites

Been a while since I posted over here. Been hard at work, building new toys.

 

Since September I've been sourcing and buying parts for a WA M4-based DMR. I am down to the last few parts that I need (hop up chamber, firing pin return spring, nozzle retaining lock, dust cover). It started out as an AABB Troy body kit and an AGM M4 that I bought for $40 off my local forum. I stripped it down to the bare aluminum, collected parts, and Duracoated the receivers, stock, and rail, then assembled the externals to take photos. What isn't AGM or new is castoff from my G&P WOC.

 

To start:

aabbreceiver1.jpg

 

Stripped:

d63d41da.jpg

 

Mockup before painting:

DSC_0007-1.jpg

 

Painted:

DSC_0016.jpg

 

Ordering most of the missing pieces this week, so that it can take its first shots by next weekend.

 

Current setup:

AGM trigger group (hammer, trigger, disconnect)

AGM auto sear

AGM nozzle (with a new o-ring) & bolt carrier

AGM buffer tube and stock

G&P lower receiver springs (all of them, pretty much)

G&P trigger, hammer and auto sear pins

G&P aluminum selector switch

AABB Troy body

Madbull DD Lite rail (interestingly enough, the AEG barrel nut that comes with this is fully compatible with AABB WA bodies)

Matrix outer barrel

KA MBSS silencer for M733

PRECISION CNC locking block (lots of frustration here - let's just say that just because it's CNC doesn't mean it's going to be an easy fit (the part looks nice, but they never cleaned it up properly on the mill, so it doesn't fit exactly right))

SHS steel firing pin

Element G27 grip in tan

 

I'm sure there's more that I did to it, but I can't think of it right now. It has the auto sear in right now because I don't have a semiauto safety switch and because I'm seriously considering a 3-round burst kit (plus, I wanna put the thing through its paces). That'll probably be removed shortly. I'll be adding a 3-9x50 scope as soon as I can order the mount.

 

Edited by vulrath

Share this post


Link to post
Share on other sites

My latest acquisition, G&P XM110, it was probably one of the last available at retail stores.

P7010001.jpg

P7010003.jpg

P7010004.jpg

 

I also bought and the G&P SR-25 sillencer for it.

P7010007.jpg

 

And here almost my entire sniper rifle collection (I forgot to include the Ares DSR-1)

DSCN1882.jpg

DSCN1885.jpg

DSCN1889.jpg

 

Older pic of my DSR-1

P8291024.jpg

 

 

Wolf

Share this post


Link to post
Share on other sites
Been a while since I posted over here. Been hard at work, building new toys.

 

Since September I've been sourcing and buying parts for a WA M4-based DMR. I am down to the last few parts that I need (hop up chamber, firing pin return spring, nozzle retaining lock, dust cover). It started out as an AABB Troy body kit and an AGM M4 that I bought for $40 off my local forum. I stripped it down to the bare aluminum, collected parts, and Duracoated the receivers, stock, and rail, then assembled the externals to take photos. What isn't AGM or new is castoff from my G&P WOC.

Which paint and where did you get said paint? I want to dark earth-ify my SR 25 and don't want to drop a ton of money but have it look nice too!

 

A&K SR25.

 

I plan on doing a few upgrades outside the gear box, like a tightbore and bucking. But for now, my eyes are on a side arm!

 

469824_10150911056651589_236203741_o.jpg

Share this post


Link to post
Share on other sites

My CQB G-Spec :D

 

 

I have shortened the barrel a little bit, as well as attaching a surefire muzzle break/suppressor. Made a TDC out of a scope adjustment, as well as tweaking the hop arms themselves. A little work on the cylinder set, and trigger.

 

P7115007.jpg

P7115003.jpg

P7115008.jpg

P7115006.jpg

Finished rifle, well besides the little tweaks and what not that we all do to our rifles.

 

P7044995.jpg

Surefire Muzzle break before paint.

 

Not sure if I like the scope or the red dot...........

Edited by woogie_man

Share this post


Link to post
Share on other sites
This my poopie, the Dragunov SVD, made by Atoz Armaments. Sorry for the low quality images, all I have is my verizon camera phone.

 

 

dragunov6.jpg

 

dragunov2.jpg

 

dragunov1.jpg

 

dragunov5.jpg

 

These pictures are of the scope I got of shortyusa. It is absolutely amazing, it is hands down the best scope I have ever used. The angles I got make the crosshairs look off center, but they really aren't, they are very precise.

 

dragunov4.jpg

 

dragunov3.jpg

 

This next picture is of me and my UTG M324 with the ghillie job I did on it. I used cut up BDU camo pants, twine from Home Depot, and double sided scotch tape. That game I completely invisible. Every single kill of the day was mine, if someone was shot, I shot them. Also, there wasn't a single casualty on my team. By the way I purposely stuck out in the picture to look good, otherwise I'd be hidden much better.

 

 

14006979_l.jpg

 

not to be a complete jerk, but your sniping position sucks. your gun should not stick out into the middle of the ditch like some demented branch. you should be laying so that your muzzle goes to the end of the flat bit. otherwise, if anyone is coming to your POS and they see the "demented branch" they will know you're there and you'll be out of the game before you can scope in. If you're gonna be a sniper, then you have to camouflage with your environment or you'll never complete your objective.

 

Share this post


Link to post
Share on other sites
Which paint and where did you get said paint? I want to dark earth-ify my SR 25 and don't want to drop a ton of money but have it look nice too!

 

It's Duracoat. It's not cheap (well, if you already had the airbrush and compressor like I did then it's reasonable), but I totally think it's worth it.

 

There's a SR25 GBBR? Dream gun. *drool*

Edited by vulrath

Share this post


Link to post
Share on other sites

My real sword SVD

 

Decided I've seen enough reddish wood furniture on SVD's, stained my wood a ebony coat (not liking how it turned out might go a little lighter next time around)

Real steel handguards w/ attached rail - Got them through Solar Tactical in CA - Has some russian print inside guessing it's made there.

Mojii Replica scope

Real steel Aimpoint mount - had an extra one laying around

Reel steel Ak/SVD side mount had laying around too.

The houge grip took off my glock to butcher.

 

 

Changed the bucking to a hardtype, new hop up system, MB Sharkfin nub

 

Plan on adding a m140 spring, TBB still debating on a 650 or 690mm, install a mosfet, lipo and wire for deans.

 

IMG_2494.jpg

IMG_2493.jpg

IMG_2492.jpg

IMG_2491.jpg

Share this post


Link to post
Share on other sites

Here is a pic of a few of my rifles.

 

IMAG0904.jpg

Agm l96

IMAG0903.jpg

 

IMAG0902.jpg

Both Bar10's "one with my M28 stock"

IMAG0726.jpg

 

IMAG0725.jpg

 

IMAG0728.jpg

 

Newest pic of my beloved M28. I have to repaint it since I put my rifle back together cause I have a new piston, I was using the stock for my Bar10 after the M28 piston blew.

 

I shortened the stock in front by a few inches, cut the barrel short and made a suppressor, and took off the adjustable buttplate. I cut a little off my original Bar10 stock and mounted it onto the M28 stock to make it lighter. This sucker ROCKS!

IMAG0935.jpg

 

I will post more pics after she is finished and painted.

 

IMAG0957.jpg

IMAG0963.jpg

Edited by Ranger420

Share this post


Link to post
Share on other sites

(Click the pictures for the full size)

th_P8060006.jpg th_P8060003.jpg

 

It may not look like much now but I have great plans for this rifle.

 

When I got the rifle, it had a PDI V Trigger, a Laylax tight bore, spring, piston, spring guide and piston head. I threw everything else out, and put all of those parts onto a Tokyo Marui receiver, I replaced the clone hopup with the TM one, and put it into a TM stock.

 

I already filled all of the spare space with foam. I plan on getting 3 PDI parts to make this rifle shine. A light Bull barrel (Pro sniper length), barrel spacers and a threaded end cap so I can put on my 30mm x 200mm King Arms foam filled supressor. The outer barrel is 27mm in diameter, so it will look really good. After that all I need is a scope rail and a good scope, then I'll be in business. Also planning on getting a Nine ball bucking.

Share this post


Link to post
Share on other sites

HPA KC02

Enjoy hope you like it.

 

Specs:

Ra tech:

6.01 TBB, 510mm

steel bolt

steel charge handle

mag release

hopup bucking

 

Tactical Specialist Custom:

Renforced steel:

fire pin, disconnector & guide bead

trigger&sear

hammer & hammer strut

Piston

 

HPA KC02 build

BTW don't use the Silicon Spray! Use GHK Silicone Drops from Evike, or some Silicone for rc car shocks.

 

 

 

Chronoing with .40s FPS is very consisten.

 

 

Shooting 300ft

Share this post


Link to post
Share on other sites
this is mine I havent had it for too long so its all stock but I make a home made suppressor which actually makes the rifle alot quieter than before all you can hear downrange is the bb hit the target

Is that the Well G96? I ask because it looks like it and I also see that you removed the folding stock knuckle. I too did the same with mine.

Share this post


Link to post
Share on other sites
Is that the Well G96? I ask because it looks like it and I also see that you removed the folding stock knuckle. I too did the same with mine.

 

No its a Matrix AW-338 the folding knuckle actually broke off but I went down to home depot and found that aluminum bar that fit in the skeleton of the gun screwed that in after some measuring and some cutting fits like it was made for it doesnt move the site I bought it from wanted $70 for repairs and S&H I fixed it in an hour for $15 I actually like it better like that

Share this post


Link to post
Share on other sites
No its a Matrix AW-338 the folding knuckle actually broke off but I went down to home depot and found that aluminum bar that fit in the skeleton of the gun screwed that in after some measuring and some cutting fits like it was made for it doesnt move the site I bought it from wanted $70 for repairs and S&H I fixed it in an hour for $15 I actually like it better like that

 

 

Well Careful of that Bolt lock on the receiver there, If the matrix's are anything like the Well's (im pretty sure they are, just rebrands) then that will be next to go, along with hopup adjustment arm, mine snapped off right where the spring puts tension on the arm, and my bolt lock split in half right on the pin, I had to CNC mill some out because I couldnt find spares anywhere. Other than that, a Nice 6.01tbb, A+ bucking and its a killing machine.

Share this post


Link to post
Share on other sites
Well Careful of that Bolt lock on the receiver there, If the matrix's are anything like the Well's (im pretty sure they are, just rebrands) then that will be next to go, along with hopup adjustment arm, mine snapped off right where the spring puts tension on the arm, and my bolt lock split in half right on the pin, I had to CNC mill some out because I couldnt find spares anywhere. Other than that, a Nice 6.01tbb, A+ bucking and its a killing machine.

 

thanks for the advice ill defiantly look into that and keep an eye on mine

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...